Не загружается система

frostu-kun	# 10 лет, 11 месяцев назад
Темы: 1 Сообщения: 6 Участник с: 19 ноября 2011	Доброго времени суток! Появилась проблема после перезагрузки с винды на арч. Во время fsck home раздела при загрузке повисает. systemd-fsck[205]: /dev/sdb2: clean, xxx/yyy files, xxx/yyy blocks Хотелось бы узнать в чем проблема. Знал бы как сделать логи прикрепил бы.. Пробовал скипнуть fsck, проблема осталась.

# 10 лет, 11 месяцев назад

Сообщения: 6

Участник с: 19 ноября 2011

Доброго времени суток!
Появилась проблема после перезагрузки с винды на арч.
Во время fsck home раздела при загрузке повисает.

systemd-fsck[205]: /dev/sdb2: clean, xxx/yyy files, xxx/yyy blocks

Хотелось бы узнать в чем проблема. Знал бы как сделать логи прикрепил бы..
Пробовал скипнуть fsck, проблема осталась.

lampslave	# 10 лет, 11 месяцев назад
Темы: 32 Сообщения: 4801 Участник с: 05 июля 2011	Ну как бы проблема говорит сама за себя. Попробуйте проверить с livecd и smart винта посмотрите.

frostu-kun	# 10 лет, 11 месяцев назад
Темы: 1 Сообщения: 6 Участник с: 19 ноября 2011	lampslave Ну как бы проблема говорит сама за себя. Попробуйте проверить с livecd и smart винта посмотрите. Запускался с убунты, home абсолютно жив, проверил его Gpartedом, все в порядке. Что такое smart?

lampslave	# 10 лет, 11 месяцев назад
Темы: 32 Сообщения: 4801 Участник с: 05 июля 2011	Я что-то не слышал, чтобы gparted умел проверять файловую систему. Попробуйте загрузиться ещё раз и проверить fsck. Не уверен, что smartctl есть на livecd с Убунтой, но всё же интересно было бы посмотреть, что выдаст smartctl -a /dev/sdb Только букву лучше проверить, на livecd она может быть другой.

lampslave

# 10 лет, 11 месяцев назад

Темы: 32

Сообщения: 4801

Участник с: 05 июля 2011

Я что-то не слышал, чтобы gparted умел проверять файловую систему. Попробуйте загрузиться ещё раз и проверить fsck. Не уверен, что smartctl есть на livecd с Убунтой, но всё же интересно было бы посмотреть, что выдаст

smartctl -a /dev/sdb

Только букву лучше проверить, на livecd она может быть другой.

frostu-kun	# 10 лет, 11 месяцев назад
Темы: 1 Сообщения: 6 Участник с: 19 ноября 2011	smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.11.2-1-ARCH] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Fujitsu MHW BH Device Model: FUJITSU MHW2160BH Serial Number: K10BT7A2A128 LU WWN Device Id: 5 00000e 0410203b2 Firmware Version: 0085001C User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 1.5 Gb/s Local Time is: Fri Oct 18 21:40:23 2013 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 649) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 92) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 19809 2 Throughput_Performance 0x0004 100 100 000 Old_age Offline - 39583744 3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 3817 5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 0 (2000 0) 7 Seek_Error_Rate 0x000e 100 100 000 Old_age Always - 2494 8 Seek_Time_Performance 0x0004 100 100 000 Old_age Offline - 0 9 Power_On_Hours 0x0032 059 059 000 Old_age Always - 20752 10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3115 191 G-Sense_Error_Rate 0x0012 100 100 000 Old_age Always - 770 192 Power-Off_Retract_Count 0x0032 098 098 000 Old_age Always - 534 194 Temperature_Celsius 0x0022 100 085 000 Old_age Always - 37 (Min/Max 7/63) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 36 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 (0 7000) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x000e 100 100 000 Old_age Always - 10019 201 Soft_Read_Error_Rate 0x0010 100 100 000 Old_age Offline - 0 203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 1529122583188 225 Load_Cycle_Count 0x0032 085 085 000 Old_age Always - 313875 240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 76 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 76 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 f9 0a 62 e0 Error: ICRC, ABRT at LBA = 0x00620af9 = 6425337 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 80 7a 0a 62 e0 00 07:18:30.919 WRITE DMA EXT 35 00 80 fa 09 62 e0 00 07:18:30.898 WRITE DMA EXT 35 00 80 7a 09 62 e0 00 07:18:30.877 WRITE DMA EXT 35 00 80 fa 08 62 e0 00 07:18:30.856 WRITE DMA EXT 35 00 80 7a 08 62 e0 00 07:18:30.835 WRITE DMA EXT Error 75 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 79 0f 5e e0 Error: ICRC, ABRT at LBA = 0x005e0f79 = 6164345 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 80 fa 0e 5e e0 00 07:16:50.604 WRITE DMA EXT 35 00 80 7a 0e 5e e0 00 07:16:50.583 WRITE DMA EXT 35 00 80 fa 0d 5e e0 00 07:16:50.562 WRITE DMA EXT 35 00 80 7a 0d 5e e0 00 07:16:50.541 WRITE DMA EXT 35 00 80 fa 0c 5e e0 00 07:16:50.521 WRITE DMA EXT Error 74 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 79 a2 3d e0 Error: ICRC, ABRT at LBA = 0x003da279 = 4039289 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 80 fa a1 3d e0 00 07:10:27.945 WRITE DMA EXT 35 00 80 7a a1 3d e0 00 07:10:27.924 WRITE DMA EXT 35 00 80 fa a0 3d e0 00 07:10:27.903 WRITE DMA EXT 35 00 80 7a a0 3d e0 00 07:10:27.882 WRITE DMA EXT 35 00 80 fa 9f 3d e0 00 07:10:27.861 WRITE DMA EXT Error 73 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 79 94 1b e0 Error: ICRC, ABRT at LBA = 0x001b9479 = 1807481 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 80 fa 93 1b e0 00 07:03:51.028 WRITE DMA EXT 35 00 80 7a 93 1b e0 00 07:03:51.007 WRITE DMA EXT 35 00 80 fa 92 1b e0 00 07:03:50.987 WRITE DMA EXT 35 00 80 7a 92 1b e0 00 07:03:50.966 WRITE DMA EXT 35 00 80 fa 91 1b e0 00 07:03:50.945 WRITE DMA EXT Error 72 occurred at disk power-on lifetime: 18585 hours (774 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 f9 48 04 e0 Error: ICRC, ABRT at LBA = 0x000448f9 = 280825 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 80 7a 48 04 e0 00 06:58:58.417 WRITE DMA EXT 35 00 80 fa 47 04 e0 00 06:58:58.406 WRITE DMA EXT 35 00 80 7a 47 04 e0 00 06:58:58.385 WRITE DMA EXT 35 00 80 fa 46 04 e0 00 06:58:58.364 WRITE DMA EXT 35 00 80 7a 46 04 e0 00 06:58:58.344 WRITE DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 20752 - # 2 Short offline Completed without error 00% 1 - # 3 Short offline Completed without error 00% 0 - # 4 Short offline Interrupted (host reset) 90% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

frostu-kun

# 10 лет, 11 месяцев назад

Темы: 1

Сообщения: 6

Участник с: 19 ноября 2011

smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.11.2-1-ARCH] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family:     Fujitsu MHW BH
Device Model:     FUJITSU MHW2160BH
Serial Number:    K10BT7A2A128
LU WWN Device Id: 5 00000e 0410203b2
Firmware Version: 0085001C
User Capacity:    160,041,885,696 bytes [160 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 3b
SATA Version is:  SATA 2.5, 1.5 Gb/s
Local Time is:    Fri Oct 18 21:40:23 2013 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever
					been run.
Total time to complete Offline
data collection: 		(  649) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  92) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   100   046    Pre-fail  Always       -       19809
  2 Throughput_Performance  0x0004   100   100   000    Old_age   Offline      -       39583744
  3 Spin_Up_Time            0x0003   100   100   025    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   099   099   000    Old_age   Always       -       3817
  5 Reallocated_Sector_Ct   0x0033   100   100   024    Pre-fail  Always       -       0 (2000 0)
  7 Seek_Error_Rate         0x000e   100   100   000    Old_age   Always       -       2494
  8 Seek_Time_Performance   0x0004   100   100   000    Old_age   Offline      -       0
  9 Power_On_Hours          0x0032   059   059   000    Old_age   Always       -       20752
 10 Spin_Retry_Count        0x0012   100   100   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       3115
191 G-Sense_Error_Rate      0x0012   100   100   000    Old_age   Always       -       770
192 Power-Off_Retract_Count 0x0032   098   098   000    Old_age   Always       -       534
194 Temperature_Celsius     0x0022   100   085   000    Old_age   Always       -       37 (Min/Max 7/63)
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       -       36
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0 (0 7000)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x000e   100   100   000    Old_age   Always       -       10019
201 Soft_Read_Error_Rate    0x0010   100   100   000    Old_age   Offline      -       0
203 Run_Out_Cancel          0x0002   100   100   000    Old_age   Always       -       1529122583188
225 Load_Cycle_Count        0x0032   085   085   000    Old_age   Always       -       313875
240 Head_Flying_Hours       0x003e   200   200   000    Old_age   Always       -       0
SMART Error Log Version: 1
ATA Error Count: 76 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 76 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 f9 0a 62 e0  Error: ICRC, ABRT at LBA = 0x00620af9 = 6425337
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 80 7a 0a 62 e0 00      07:18:30.919  WRITE DMA EXT
  35 00 80 fa 09 62 e0 00      07:18:30.898  WRITE DMA EXT
  35 00 80 7a 09 62 e0 00      07:18:30.877  WRITE DMA EXT
  35 00 80 fa 08 62 e0 00      07:18:30.856  WRITE DMA EXT
  35 00 80 7a 08 62 e0 00      07:18:30.835  WRITE DMA EXT
Error 75 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 79 0f 5e e0  Error: ICRC, ABRT at LBA = 0x005e0f79 = 6164345
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 80 fa 0e 5e e0 00      07:16:50.604  WRITE DMA EXT
  35 00 80 7a 0e 5e e0 00      07:16:50.583  WRITE DMA EXT
  35 00 80 fa 0d 5e e0 00      07:16:50.562  WRITE DMA EXT
  35 00 80 7a 0d 5e e0 00      07:16:50.541  WRITE DMA EXT
  35 00 80 fa 0c 5e e0 00      07:16:50.521  WRITE DMA EXT
Error 74 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 79 a2 3d e0  Error: ICRC, ABRT at LBA = 0x003da279 = 4039289
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 80 fa a1 3d e0 00      07:10:27.945  WRITE DMA EXT
  35 00 80 7a a1 3d e0 00      07:10:27.924  WRITE DMA EXT
  35 00 80 fa a0 3d e0 00      07:10:27.903  WRITE DMA EXT
  35 00 80 7a a0 3d e0 00      07:10:27.882  WRITE DMA EXT
  35 00 80 fa 9f 3d e0 00      07:10:27.861  WRITE DMA EXT
Error 73 occurred at disk power-on lifetime: 18586 hours (774 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 79 94 1b e0  Error: ICRC, ABRT at LBA = 0x001b9479 = 1807481
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 80 fa 93 1b e0 00      07:03:51.028  WRITE DMA EXT
  35 00 80 7a 93 1b e0 00      07:03:51.007  WRITE DMA EXT
  35 00 80 fa 92 1b e0 00      07:03:50.987  WRITE DMA EXT
  35 00 80 7a 92 1b e0 00      07:03:50.966  WRITE DMA EXT
  35 00 80 fa 91 1b e0 00      07:03:50.945  WRITE DMA EXT
Error 72 occurred at disk power-on lifetime: 18585 hours (774 days + 9 hours)
  When the command that caused the error occurred, the device was active or idle.
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 f9 48 04 e0  Error: ICRC, ABRT at LBA = 0x000448f9 = 280825
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 80 7a 48 04 e0 00      06:58:58.417  WRITE DMA EXT
  35 00 80 fa 47 04 e0 00      06:58:58.406  WRITE DMA EXT
  35 00 80 7a 47 04 e0 00      06:58:58.385  WRITE DMA EXT
  35 00 80 fa 46 04 e0 00      06:58:58.364  WRITE DMA EXT
  35 00 80 7a 46 04 e0 00      06:58:58.344  WRITE DMA EXT
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     20752         -
# 2  Short offline       Completed without error       00%         1         -
# 3  Short offline       Completed without error       00%         0         -
# 4  Short offline       Interrupted (host reset)      90%         0         -
SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

lampslave	# 10 лет, 11 месяцев назад
Темы: 32 Сообщения: 4801 Участник с: 05 июля 2011	200 Multi_Zone_Error_Rate 0x000e 100 100 000 Old_age Always - 10019 Атрибут: 200 (С8) Write Error Rate (MultiZone Error Rate). Тип: текущий. Описание: содержит частоту возникновения ошибок при записи. Ненулевое значение говорит о проблемах с диском, в частности, у дисков WD большие цифры могут означать «умирающие» головки. http://forum.ixbt.com/post.cgi?id=annc:11:36706 Хотя threshold почему-то на нуле, странно. А fsck там как?

lampslave

# 10 лет, 11 месяцев назад

Темы: 32

Сообщения: 4801

Участник с: 05 июля 2011

200 Multi_Zone_Error_Rate   0x000e   100   100   000    Old_age   Always       -       10019

Атрибут: 200 (С8) Write Error Rate (MultiZone Error Rate).
Тип: текущий.
Описание: содержит частоту возникновения ошибок при записи.
Ненулевое значение говорит о проблемах с диском, в частности, у дисков WD большие цифры могут означать «умирающие» головки.
http://forum.ixbt.com/post.cgi?id=annc:11:36706

Хотя threshold почему-то на нуле, странно.

А fsck там как?

frostu-kun	# 10 лет, 11 месяцев назад
Темы: 1 Сообщения: 6 Участник с: 19 ноября 2011	Как сделать проверку fsck?

nafanja	# 10 лет, 11 месяцев назад
Темы: 94 Сообщения: 9252 Участник с: 02 июня 2012 заблокирован	fsck -f /dev/sdX это лучше с лайф сд делать, что бы были не примонтированы разделы. Псевдографический инсталлятор Arch Linux ver. 3.8.2 Благодарности принимаются на ЯД 410012815723874

frostu-kun	# 10 лет, 11 месяцев назад
Темы: 1 Сообщения: 6 Участник с: 19 ноября 2011	nafanja fsck -f /dev/sdX это лучше с лайф сд делать, что бы были не примонтированы разделы. /dev/sdb2: 19681/6496256 files (1.9% non-contiguous), 2651742/25965270 blocks

corner	# 10 лет, 11 месяцев назад
Темы: 6 Сообщения: 773 Участник с: 21 июля 2011	Если копьютер стационарный, попробуйте проверить (передернуть, или заменить) шлейф диска. Они иногда слетают.