Странное поведение ядра при попытках подключения USB хаба

Vorobuska	# 3 года, 10 месяцев назад (отредактировано 3 года, 10 месяцев назад)
Темы: 4 Сообщения: 10 Участник с: 24 июля 2020	Железо: Ноутбук ASUS, единственный исправный USB 3.0 порт (к которому, собственно, USB hub и подключается), 2 гига оперативы, встроенная видеопамять ПО: Arch Linux x86_64, ядро: 5.13.5-arch1-1, DE: xfce4 Проблема проявляется с Havic HV-H18 (единственный доступный мне USB hub, нормально работает с Windows 8), GRUB видит все мои устройства на хабе (определял по индикатору caps lock на клавиатуре) и работает так же гладко как и на Windows, но когда я загружаюсь в Arch Linux в 80% случаев у меня просто отваливается хаб, и порт перестает работать до перезагрузки, с такой же вероятностью он отваливается если я подключаю его с уже загруженной системой Я уже прошёлся по некоторым темам в и вне форума, но решения мне не подошли (или я их проворонил), перечислить ссылки не могу, т.к недавно чистил историю, но вот то, что я восстановил из консоли: 1) Я пытался выключить /sys/module/usbcore/parameters/autosuspend, отправив туда -1 (оценить успешность метода не могу, тогда все работало и после восстановления настроек) 2) Во время отключения USB хаба в терминале возникает следующая ошибка: xhci_hcd 0000:03:00.0: xHCI host not responding to stop endpoint command. xhci_hcd 0000:03:00.0: USBSTS: xhci_hcd 0000:03:00.0: xHCI host controller not responding, assume dead xhci_hcd 0000:03:00.0: HC died; cleaning up usb 3-1: USB disconnect, device number 4 usb 3-1.3: USB disconnect, device number 5 usb 3-1.4: USB disconnect, device number 6 3) lsusb -t до отключения и после содержит запись о порте, но подключения к нему не отображаются, да и порт после отключения хаба, как я уже говорил, до перезапуска не работает

# 3 года, 10 месяцев назад (отредактировано 3 года, 10 месяцев назад)

Сообщения: 10

Участник с: 24 июля 2020

Железо:
Ноутбук ASUS, единственный исправный USB 3.0 порт (к которому, собственно, USB hub и подключается), 2 гига оперативы, встроенная видеопамять

ПО:
Arch Linux x86_64, ядро: 5.13.5-arch1-1, DE: xfce4

Проблема проявляется с Havic HV-H18 (единственный доступный мне USB hub, нормально работает с Windows 8), GRUB видит все мои устройства на хабе (определял по индикатору caps lock на клавиатуре) и работает так же гладко как и на Windows, но когда я загружаюсь в Arch Linux в 80% случаев у меня просто отваливается хаб, и порт перестает работать до перезагрузки, с такой же вероятностью он отваливается если я подключаю его с уже загруженной системой

Я уже прошёлся по некоторым темам в и вне форума, но решения мне не подошли (или я их проворонил), перечислить ссылки не могу, т.к недавно чистил историю, но вот то, что я восстановил из консоли:

1) Я пытался выключить /sys/module/usbcore/parameters/autosuspend, отправив туда -1 (оценить успешность метода не могу, тогда все работало и после восстановления настроек)

2) Во время отключения USB хаба в терминале возникает следующая ошибка:
xhci_hcd 0000:03:00.0: xHCI host not responding to stop endpoint command.
xhci_hcd 0000:03:00.0: USBSTS:
xhci_hcd 0000:03:00.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:03:00.0: HC died; cleaning up
usb 3-1: USB disconnect, device number 4
usb 3-1.3: USB disconnect, device number 5
usb 3-1.4: USB disconnect, device number 6

3) lsusb -t до отключения и после содержит запись о порте, но подключения к нему не отображаются, да и порт после отключения хаба, как я уже говорил, до перезапуска не работает

jim945	# 3 года, 10 месяцев назад
Темы: 9 Сообщения: 3194 Участник с: 25 января 2010	Ноут случайно не dell? Lupus pilum mutat, non mentem.

vs220	# 3 года, 10 месяцев назад
Темы: 25 Сообщения: 8524 Участник с: 16 августа 2009	`sudo dmesg -wH` воткнуть хаб и смотреть вывод, потом в хаб подключить что надо и тоже вывод смотреть.

Vorobuska	# 3 года, 10 месяцев назад
Темы: 4 Сообщения: 10 Участник с: 24 июля 2020	jim945 Ноут случайно не dell? Asus

Vorobuska	# 3 года, 10 месяцев назад
Темы: 4 Сообщения: 10 Участник с: 24 июля 2020	vs220 `sudo dmesg -wH` воткнуть хаб и смотреть вывод, потом в хаб подключить что надо и тоже вывод смотреть. По данному совету решил взять и мониторить логи, вот вывод: Хаб подключается успешно: [ +0.002384] hub 3-1:1.0: USB hub found [ +0.000037] hub 3-1:1.0: 4 ports detected [ +0.280677] usb 3-1.1: new low-speed USB device number 7 using xhci_hcd [ +0.105067] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10 [ +0.000010] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000004] usb 3-1.1: Product: USB Keyboard [ +0.000002] usb 3-1.1: Manufacturer: USB [ +0.006962] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.0007/input/input28 [ +0.058348] hid-generic 0003:1A2C:2C27.0007: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0 [ +0.002611] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input29 [ +0.053811] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input30 [ +0.000095] hid-generic 0003:1A2C:2C27.0008: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1 Отключение: [ +0.073094] usb 3-1.4: new full-speed USB device number 8 using xhci_hcd \| На счет этой строчки не уверен, но при штатном подключении я ее не видел [ +0.076706] usb 3-1.4: device descriptor read/64, error -32 [ +0.205404] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02 [ +0.000011] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000004] usb 3-1.4: Product: USB Device [ +0.000002] usb 3-1.4: Manufacturer: A4TECH [ +0.006377] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input31 [ +0.055346] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input32 [ +0.000276] hid-generic 0003:09DA:054F.0009: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0 [ +0.001707] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000A/input/input33 [ +0.000246] hid-generic 0003:09DA:054F.000A: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1 [Jul28 18:10] perf: interrupt took too long (2519 > 2500), lowering kernel.perf_event_max_sample_rate to 79200 И переподключение вручную [Jul28 18:23] usb 3-1: USB disconnect, device number 6 [ +0.000016] usb 3-1.1: USB disconnect, device number 7 [ +0.145846] usb 3-1.4: USB disconnect, device number 8 [ +7.478113] usb 3-1: new high-speed USB device number 10 using xhci_hcd [ +0.210285] usb 3-1: New USB device found, idVendor=214b, idProduct=7250, bcdDevice= 1.00 [ +0.000018] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ +0.000008] usb 3-1: Product: USB2.0 HUB [ +0.002668] hub 3-1:1.0: USB hub found [ +0.000906] hub 3-1:1.0: 4 ports detected [ +0.279440] usb 3-1.1: new low-speed USB device number 11 using xhci_hcd [ +0.102318] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10 [ +0.000018] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000007] usb 3-1.1: Product: USB Keyboard [ +0.000005] usb 3-1.1: Manufacturer: USB [ +0.008173] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.000B/input/input34 [ +0.057812] hid-generic 0003:1A2C:2C27.000B: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0 [ +0.003678] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input35 [ +0.054902] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input36 [ +0.000114] hid-generic 0003:1A2C:2C27.000C: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1 [ +0.072988] usb 3-1.4: new full-speed USB device number 12 using xhci_hcd [ +0.098959] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02 [ +0.000017] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000008] usb 3-1.4: Product: USB Device [ +0.000005] usb 3-1.4: Manufacturer: A4TECH [ +0.007414] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input37 [ +0.054609] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input38 [ +0.000281] hid-generic 0003:09DA:054F.000D: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0 [ +0.001320] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000E/input/input39 [ +0.000245] hid-generic 0003:09DA:054F.000E: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1 Мог что-то попутать, вот полный лог (с постороними данными) для наглядности: [ +0.000006] usb 3-1: Product: USB2.0 HUB [ +0.004254] hub 3-1:1.0: USB hub found [ +0.000470] hub 3-1:1.0: 4 ports detected [ +0.278337] usb 3-1.3: new low-speed USB device number 3 using xhci_hcd [ +0.102106] usb 3-1.3: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10 [ +0.000015] usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000007] usb 3-1.3: Product: USB Keyboard [ +0.000004] usb 3-1.3: Manufacturer: USB [ +0.077845] usb 3-1.4: new full-speed USB device number 4 using xhci_hcd [ +0.039180] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.3/3-1.3:1.0/0003:1A2C:2C27.0001/input/input19 [ +0.054526] hid-generic 0003:1A2C:2C27.0001: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.3/input0 [ +0.002814] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:1A2C:2C27.0002/input/input20 [ +0.005996] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02 [ +0.000015] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000007] usb 3-1.4: Product: USB Device [ +0.000005] usb 3-1.4: Manufacturer: A4TECH [ +0.006710] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0003/input/input22 [ +0.041119] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:1A2C:2C27.0002/input/input21 [ +0.056818] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0003/input/input23 [ +0.000172] hid-generic 0003:1A2C:2C27.0002: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.3/input1 [ +0.000197] hid-generic 0003:09DA:054F.0003: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0 [ +0.001601] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.0004/input/input24 [ +0.000316] hid-generic 0003:09DA:054F.0004: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1 [ +0.001873] usbcore: registered new interface driver usbhid [ +0.000005] usbhid: USB HID core driver [ +11.685559] audit: type=1100 audit(1627494264.478:57): pid=889 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:authentication grantors=pam_shells,pam_faillock,pam_permit,pam_faillock acct="pydevelop" exe="/usr/lib/lxdm/lxdm-session" hostname=? addr=? terminal=? res=success' [ +0.044440] audit: type=1101 audit(1627494264.521:58): pid=889 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="pydevelop" exe="/usr/lib/lxdm/lxdm-session" hostname=? addr=? terminal=? res=success' [ +0.114753] audit: type=1006 audit(1627494264.638:59): pid=889 uid=0 old-auid=4294967295 auid=214124 tty=(none) old-ses=4294967295 ses=1 res=1 [ +0.000025] audit: type=1300 audit(1627494264.638:59): arch=c000003e syscall=1 success=yes exit=6 a0=5 a1=7ffd73d53c40 a2=6 a3=3446c items=0 ppid=431 pid=889 auid=214124 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="lxdm-session" exe="/usr/lib/lxdm/lxdm-session" key=(null) [ +0.000013] audit: type=1327 audit(1627494264.638:59): proctitle="/usr/lib/lxdm/lxdm-session" [ +0.173341] audit: type=1130 audit(1627494264.808:60): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user-runtime-dir@214124 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +0.029757] audit: type=1101 audit(1627494264.838:61): pid=891 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="pydevelop" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +0.000324] audit: type=1103 audit(1627494264.838:62): pid=891 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=? acct="pydevelop" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=failed' [ +0.000010] audit: type=1006 audit(1627494264.838:63): pid=891 uid=0 old-auid=4294967295 auid=214124 tty=(none) old-ses=4294967295 ses=2 res=1 [ +0.000005] audit: type=1300 audit(1627494264.838:63): arch=c000003e syscall=1 success=yes exit=6 a0=9 a1=7ffe2c8fe320 a2=6 a3=3446c items=0 ppid=1 pid=891 auid=214124 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=2 comm="(systemd)" exe="/usr/lib/systemd/systemd" key=(null) [ +1.093240] wlp2s0: authenticate with e4:be:ed:f3:04:40 [ +0.019861] wlp2s0: send auth to e4:be:ed:f3:04:40 (try 1/3) [ +0.021945] wlp2s0: authenticated [ +0.002065] wlp2s0: associate with e4:be:ed:f3:04:40 (try 1/3) [ +0.004092] wlp2s0: RX AssocResp from e4:be:ed:f3:04:40 (capab=0x411 status=0 aid=4) [ +0.000479] wlp2s0: associated [ +0.165754] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready [ +6.589312] kauditd_printk_skb: 9 callbacks suppressed [ +0.000008] audit: type=1130 audit(1627494272.735:70): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=polkit comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +3.212049] audit: type=1130 audit(1627494275.948:71): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=rtkit-daemon comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +2.534557] audit: type=1334 audit(1627494278.481:72): prog-id=25 op=LOAD [ +0.000014] audit: type=1334 audit(1627494278.481:73): prog-id=26 op=LOAD [ +0.447140] audit: type=1131 audit(1627494278.931:74): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-dispatcher comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +1.245467] audit: type=1130 audit(1627494280.175:75): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=upower comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +6.438146] audit: type=1130 audit(1627494286.611:76): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=udisks2 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [Jul28 17:46] audit: type=1100 audit(1627494376.479:77): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:authentication grantors=pam_faillock,pam_permit,pam_faillock acct="pydevelop" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success' [ +0.002635] audit: type=1101 audit(1627494376.482:78): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:accounting grantors=pam_unix,pam_permit,pam_time acct="pydevelop" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success' [ +0.002507] audit: type=1110 audit(1627494376.486:79): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:setcred grantors=pam_faillock,pam_permit,pam_faillock acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success' [ +0.010107] audit: type=1105 audit(1627494376.496:80): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success' [ +11.435093] usb 3-1.3: USB disconnect, device number 3 [ +3.020662] usb 3-1.1: new low-speed USB device number 5 using xhci_hcd [ +0.102164] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10 [ +0.000018] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000007] usb 3-1.1: Product: USB Keyboard [ +0.000005] usb 3-1.1: Manufacturer: USB [ +0.010508] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.0005/input/input25 [ +0.055689] hid-generic 0003:1A2C:2C27.0005: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0 [ +0.003560] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0006/input/input26 [ +0.055097] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0006/input/input27 [ +0.001125] hid-generic 0003:1A2C:2C27.0006: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1 [Jul28 18:09] usb 3-1: USB disconnect, device number 2 [ +0.000009] usb 3-1.1: USB disconnect, device number 5 [ +0.103116] usb 3-1.4: USB disconnect, device number 4 [ +0.418486] usb 3-1: new high-speed USB device number 6 using xhci_hcd [ +0.213529] usb 3-1: New USB device found, idVendor=214b, idProduct=7250, bcdDevice= 1.00 [ +0.000011] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ +0.000004] usb 3-1: Product: USB2.0 HUB [ +0.002384] hub 3-1:1.0: USB hub found [ +0.000037] hub 3-1:1.0: 4 ports detected [ +0.280677] usb 3-1.1: new low-speed USB device number 7 using xhci_hcd [ +0.105067] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10 [ +0.000010] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000004] usb 3-1.1: Product: USB Keyboard [ +0.000002] usb 3-1.1: Manufacturer: USB [ +0.006962] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.0007/input/input28 [ +0.058348] hid-generic 0003:1A2C:2C27.0007: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0 [ +0.002611] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input29 [ +0.053811] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input30 [ +0.000095] hid-generic 0003:1A2C:2C27.0008: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1 [ +0.073094] usb 3-1.4: new full-speed USB device number 8 using xhci_hcd [ +0.076706] usb 3-1.4: device descriptor read/64, error -32 [ +0.205404] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02 [ +0.000011] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000004] usb 3-1.4: Product: USB Device [ +0.000002] usb 3-1.4: Manufacturer: A4TECH [ +0.006377] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input31 [ +0.055346] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input32 [ +0.000276] hid-generic 0003:09DA:054F.0009: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0 [ +0.001707] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000A/input/input33 [ +0.000246] hid-generic 0003:09DA:054F.000A: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1 [Jul28 18:10] perf: interrupt took too long (2519 > 2500), lowering kernel.perf_event_max_sample_rate to 79200 [Jul28 18:15] audit: type=1334 audit(1627496114.240:81): prog-id=27 op=LOAD [ +0.000275] audit: type=1334 audit(1627496114.240:82): prog-id=28 op=LOAD [ +0.000068] audit: type=1334 audit(1627496114.240:83): prog-id=29 op=LOAD [ +6.683668] audit: type=1130 audit(1627496120.923:84): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +30.760729] audit: type=1131 audit(1627496151.684:85): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success' [ +0.071213] audit: type=1334 audit(1627496151.757:86): prog-id=29 op=UNLOAD [ +0.000012] audit: type=1334 audit(1627496151.757:87): prog-id=28 op=UNLOAD [ +0.000005] audit: type=1334 audit(1627496151.757:88): prog-id=27 op=UNLOAD [Jul28 18:23] usb 3-1: USB disconnect, device number 6 [ +0.000016] usb 3-1.1: USB disconnect, device number 7 [ +0.145846] usb 3-1.4: USB disconnect, device number 8 [ +7.478113] usb 3-1: new high-speed USB device number 10 using xhci_hcd [ +0.210285] usb 3-1: New USB device found, idVendor=214b, idProduct=7250, bcdDevice= 1.00 [ +0.000018] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ +0.000008] usb 3-1: Product: USB2.0 HUB [ +0.002668] hub 3-1:1.0: USB hub found [ +0.000906] hub 3-1:1.0: 4 ports detected [ +0.279440] usb 3-1.1: new low-speed USB device number 11 using xhci_hcd [ +0.102318] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10 [ +0.000018] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000007] usb 3-1.1: Product: USB Keyboard [ +0.000005] usb 3-1.1: Manufacturer: USB [ +0.008173] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.000B/input/input34 [ +0.057812] hid-generic 0003:1A2C:2C27.000B: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0 [ +0.003678] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input35 [ +0.054902] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input36 [ +0.000114] hid-generic 0003:1A2C:2C27.000C: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1 [ +0.072988] usb 3-1.4: new full-speed USB device number 12 using xhci_hcd [ +0.098959] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02 [ +0.000017] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ +0.000008] usb 3-1.4: Product: USB Device [ +0.000005] usb 3-1.4: Manufacturer: A4TECH [ +0.007414] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input37 [ +0.054609] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input38 [ +0.000281] hid-generic 0003:09DA:054F.000D: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0 [ +0.001320] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000E/input/input39 [ +0.000245] hid-generic 0003:09DA:054F.000E: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1

Vorobuska

# 3 года, 10 месяцев назад

Темы: 4

Сообщения: 10

Участник с: 24 июля 2020

vs220
 sudo dmesg -wH
воткнуть хаб и смотреть вывод, потом в хаб подключить что надо и тоже вывод смотреть.

По данному совету решил взять и мониторить логи, вот вывод:

Хаб подключается успешно:

[  +0.002384] hub 3-1:1.0: USB hub found
[  +0.000037] hub 3-1:1.0: 4 ports detected
[  +0.280677] usb 3-1.1: new low-speed USB device number 7 using xhci_hcd
[  +0.105067] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10
[  +0.000010] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000004] usb 3-1.1: Product: USB Keyboard
[  +0.000002] usb 3-1.1: Manufacturer: USB
[  +0.006962] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.0007/input/input28
[  +0.058348] hid-generic 0003:1A2C:2C27.0007: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0
[  +0.002611] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input29
[  +0.053811] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input30
[  +0.000095] hid-generic 0003:1A2C:2C27.0008: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1

Отключение:

[  +0.073094] usb 3-1.4: new full-speed USB device number 8 using xhci_hcd  |  На счет этой строчки не уверен, но при штатном подключении я ее не видел
[  +0.076706] usb 3-1.4: device descriptor read/64, error -32
[  +0.205404] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02
[  +0.000011] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000004] usb 3-1.4: Product: USB Device
[  +0.000002] usb 3-1.4: Manufacturer: A4TECH
[  +0.006377] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input31
[  +0.055346] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input32
[  +0.000276] hid-generic 0003:09DA:054F.0009: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0
[  +0.001707] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000A/input/input33
[  +0.000246] hid-generic 0003:09DA:054F.000A: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1
[Jul28 18:10] perf: interrupt took too long (2519 > 2500), lowering kernel.perf_event_max_sample_rate to 79200

И переподключение вручную

[Jul28 18:23] usb 3-1: USB disconnect, device number 6
[  +0.000016] usb 3-1.1: USB disconnect, device number 7
[  +0.145846] usb 3-1.4: USB disconnect, device number 8
[  +7.478113] usb 3-1: new high-speed USB device number 10 using xhci_hcd
[  +0.210285] usb 3-1: New USB device found, idVendor=214b, idProduct=7250, bcdDevice= 1.00
[  +0.000018] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  +0.000008] usb 3-1: Product: USB2.0 HUB
[  +0.002668] hub 3-1:1.0: USB hub found
[  +0.000906] hub 3-1:1.0: 4 ports detected
[  +0.279440] usb 3-1.1: new low-speed USB device number 11 using xhci_hcd
[  +0.102318] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10
[  +0.000018] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000007] usb 3-1.1: Product: USB Keyboard
[  +0.000005] usb 3-1.1: Manufacturer: USB
[  +0.008173] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.000B/input/input34
[  +0.057812] hid-generic 0003:1A2C:2C27.000B: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0
[  +0.003678] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input35
[  +0.054902] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input36
[  +0.000114] hid-generic 0003:1A2C:2C27.000C: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1
[  +0.072988] usb 3-1.4: new full-speed USB device number 12 using xhci_hcd
[  +0.098959] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02
[  +0.000017] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000008] usb 3-1.4: Product: USB Device
[  +0.000005] usb 3-1.4: Manufacturer: A4TECH
[  +0.007414] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input37
[  +0.054609] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input38
[  +0.000281] hid-generic 0003:09DA:054F.000D: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0
[  +0.001320] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000E/input/input39
[  +0.000245] hid-generic 0003:09DA:054F.000E: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1

Мог что-то попутать, вот полный лог (с постороними данными) для наглядности:

[  +0.000006] usb 3-1: Product: USB2.0 HUB
[  +0.004254] hub 3-1:1.0: USB hub found
[  +0.000470] hub 3-1:1.0: 4 ports detected
[  +0.278337] usb 3-1.3: new low-speed USB device number 3 using xhci_hcd
[  +0.102106] usb 3-1.3: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10
[  +0.000015] usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000007] usb 3-1.3: Product: USB Keyboard
[  +0.000004] usb 3-1.3: Manufacturer: USB
[  +0.077845] usb 3-1.4: new full-speed USB device number 4 using xhci_hcd
[  +0.039180] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.3/3-1.3:1.0/0003:1A2C:2C27.0001/input/input19
[  +0.054526] hid-generic 0003:1A2C:2C27.0001: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.3/input0
[  +0.002814] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:1A2C:2C27.0002/input/input20
[  +0.005996] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02
[  +0.000015] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000007] usb 3-1.4: Product: USB Device
[  +0.000005] usb 3-1.4: Manufacturer: A4TECH
[  +0.006710] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0003/input/input22
[  +0.041119] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.3/3-1.3:1.1/0003:1A2C:2C27.0002/input/input21
[  +0.056818] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0003/input/input23
[  +0.000172] hid-generic 0003:1A2C:2C27.0002: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.3/input1
[  +0.000197] hid-generic 0003:09DA:054F.0003: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0
[  +0.001601] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.0004/input/input24
[  +0.000316] hid-generic 0003:09DA:054F.0004: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1
[  +0.001873] usbcore: registered new interface driver usbhid
[  +0.000005] usbhid: USB HID core driver
[ +11.685559] audit: type=1100 audit(1627494264.478:57): pid=889 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:authentication grantors=pam_shells,pam_faillock,pam_permit,pam_faillock acct="pydevelop" exe="/usr/lib/lxdm/lxdm-session" hostname=? addr=? terminal=? res=success'
[  +0.044440] audit: type=1101 audit(1627494264.521:58): pid=889 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="pydevelop" exe="/usr/lib/lxdm/lxdm-session" hostname=? addr=? terminal=? res=success'
[  +0.114753] audit: type=1006 audit(1627494264.638:59): pid=889 uid=0 old-auid=4294967295 auid=214124 tty=(none) old-ses=4294967295 ses=1 res=1
[  +0.000025] audit: type=1300 audit(1627494264.638:59): arch=c000003e syscall=1 success=yes exit=6 a0=5 a1=7ffd73d53c40 a2=6 a3=3446c items=0 ppid=431 pid=889 auid=214124 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=1 comm="lxdm-session" exe="/usr/lib/lxdm/lxdm-session" key=(null)
[  +0.000013] audit: type=1327 audit(1627494264.638:59): proctitle="/usr/lib/lxdm/lxdm-session"
[  +0.173341] audit: type=1130 audit(1627494264.808:60): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user-runtime-dir@214124 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  +0.029757] audit: type=1101 audit(1627494264.838:61): pid=891 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="pydevelop" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  +0.000324] audit: type=1103 audit(1627494264.838:62): pid=891 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=? acct="pydevelop" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=failed'
[  +0.000010] audit: type=1006 audit(1627494264.838:63): pid=891 uid=0 old-auid=4294967295 auid=214124 tty=(none) old-ses=4294967295 ses=2 res=1
[  +0.000005] audit: type=1300 audit(1627494264.838:63): arch=c000003e syscall=1 success=yes exit=6 a0=9 a1=7ffe2c8fe320 a2=6 a3=3446c items=0 ppid=1 pid=891 auid=214124 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=2 comm="(systemd)" exe="/usr/lib/systemd/systemd" key=(null)
[  +1.093240] wlp2s0: authenticate with e4:be:ed:f3:04:40
[  +0.019861] wlp2s0: send auth to e4:be:ed:f3:04:40 (try 1/3)
[  +0.021945] wlp2s0: authenticated
[  +0.002065] wlp2s0: associate with e4:be:ed:f3:04:40 (try 1/3)
[  +0.004092] wlp2s0: RX AssocResp from e4:be:ed:f3:04:40 (capab=0x411 status=0 aid=4)
[  +0.000479] wlp2s0: associated
[  +0.165754] IPv6: ADDRCONF(NETDEV_CHANGE): wlp2s0: link becomes ready
[  +6.589312] kauditd_printk_skb: 9 callbacks suppressed
[  +0.000008] audit: type=1130 audit(1627494272.735:70): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=polkit comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  +3.212049] audit: type=1130 audit(1627494275.948:71): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=rtkit-daemon comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  +2.534557] audit: type=1334 audit(1627494278.481:72): prog-id=25 op=LOAD
[  +0.000014] audit: type=1334 audit(1627494278.481:73): prog-id=26 op=LOAD
[  +0.447140] audit: type=1131 audit(1627494278.931:74): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=NetworkManager-dispatcher comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  +1.245467] audit: type=1130 audit(1627494280.175:75): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=upower comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  +6.438146] audit: type=1130 audit(1627494286.611:76): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=udisks2 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[Jul28 17:46] audit: type=1100 audit(1627494376.479:77): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:authentication grantors=pam_faillock,pam_permit,pam_faillock acct="pydevelop" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success'
[  +0.002635] audit: type=1101 audit(1627494376.482:78): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:accounting grantors=pam_unix,pam_permit,pam_time acct="pydevelop" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success'
[  +0.002507] audit: type=1110 audit(1627494376.486:79): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:setcred grantors=pam_faillock,pam_permit,pam_faillock acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success'
[  +0.010107] audit: type=1105 audit(1627494376.496:80): pid=1291 uid=214124 auid=214124 ses=1 msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/0 res=success'
[ +11.435093] usb 3-1.3: USB disconnect, device number 3
[  +3.020662] usb 3-1.1: new low-speed USB device number 5 using xhci_hcd
[  +0.102164] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10
[  +0.000018] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000007] usb 3-1.1: Product: USB Keyboard
[  +0.000005] usb 3-1.1: Manufacturer: USB
[  +0.010508] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.0005/input/input25
[  +0.055689] hid-generic 0003:1A2C:2C27.0005: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0
[  +0.003560] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0006/input/input26
[  +0.055097] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0006/input/input27
[  +0.001125] hid-generic 0003:1A2C:2C27.0006: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1
[Jul28 18:09] usb 3-1: USB disconnect, device number 2
[  +0.000009] usb 3-1.1: USB disconnect, device number 5
[  +0.103116] usb 3-1.4: USB disconnect, device number 4
[  +0.418486] usb 3-1: new high-speed USB device number 6 using xhci_hcd
[  +0.213529] usb 3-1: New USB device found, idVendor=214b, idProduct=7250, bcdDevice= 1.00
[  +0.000011] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  +0.000004] usb 3-1: Product: USB2.0 HUB
[  +0.002384] hub 3-1:1.0: USB hub found
[  +0.000037] hub 3-1:1.0: 4 ports detected
[  +0.280677] usb 3-1.1: new low-speed USB device number 7 using xhci_hcd
[  +0.105067] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10
[  +0.000010] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000004] usb 3-1.1: Product: USB Keyboard
[  +0.000002] usb 3-1.1: Manufacturer: USB
[  +0.006962] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.0007/input/input28
[  +0.058348] hid-generic 0003:1A2C:2C27.0007: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0
[  +0.002611] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input29
[  +0.053811] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.0008/input/input30
[  +0.000095] hid-generic 0003:1A2C:2C27.0008: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1
[  +0.073094] usb 3-1.4: new full-speed USB device number 8 using xhci_hcd
[  +0.076706] usb 3-1.4: device descriptor read/64, error -32
[  +0.205404] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02
[  +0.000011] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000004] usb 3-1.4: Product: USB Device
[  +0.000002] usb 3-1.4: Manufacturer: A4TECH
[  +0.006377] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input31
[  +0.055346] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.0009/input/input32
[  +0.000276] hid-generic 0003:09DA:054F.0009: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0
[  +0.001707] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000A/input/input33
[  +0.000246] hid-generic 0003:09DA:054F.000A: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1
[Jul28 18:10] perf: interrupt took too long (2519 > 2500), lowering kernel.perf_event_max_sample_rate to 79200
[Jul28 18:15] audit: type=1334 audit(1627496114.240:81): prog-id=27 op=LOAD
[  +0.000275] audit: type=1334 audit(1627496114.240:82): prog-id=28 op=LOAD
[  +0.000068] audit: type=1334 audit(1627496114.240:83): prog-id=29 op=LOAD
[  +6.683668] audit: type=1130 audit(1627496120.923:84): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[ +30.760729] audit: type=1131 audit(1627496151.684:85): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  +0.071213] audit: type=1334 audit(1627496151.757:86): prog-id=29 op=UNLOAD
[  +0.000012] audit: type=1334 audit(1627496151.757:87): prog-id=28 op=UNLOAD
[  +0.000005] audit: type=1334 audit(1627496151.757:88): prog-id=27 op=UNLOAD
[Jul28 18:23] usb 3-1: USB disconnect, device number 6
[  +0.000016] usb 3-1.1: USB disconnect, device number 7
[  +0.145846] usb 3-1.4: USB disconnect, device number 8
[  +7.478113] usb 3-1: new high-speed USB device number 10 using xhci_hcd
[  +0.210285] usb 3-1: New USB device found, idVendor=214b, idProduct=7250, bcdDevice= 1.00
[  +0.000018] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  +0.000008] usb 3-1: Product: USB2.0 HUB
[  +0.002668] hub 3-1:1.0: USB hub found
[  +0.000906] hub 3-1:1.0: 4 ports detected
[  +0.279440] usb 3-1.1: new low-speed USB device number 11 using xhci_hcd
[  +0.102318] usb 3-1.1: New USB device found, idVendor=1a2c, idProduct=2c27, bcdDevice= 1.10
[  +0.000018] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000007] usb 3-1.1: Product: USB Keyboard
[  +0.000005] usb 3-1.1: Manufacturer: USB
[  +0.008173] input: USB USB Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.0/0003:1A2C:2C27.000B/input/input34
[  +0.057812] hid-generic 0003:1A2C:2C27.000B: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keyboard] on usb-0000:03:00.0-1.1/input0
[  +0.003678] input: USB USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input35
[  +0.054902] input: USB USB Keyboard System Control as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.1/3-1.1:1.1/0003:1A2C:2C27.000C/input/input36
[  +0.000114] hid-generic 0003:1A2C:2C27.000C: input,hidraw1: USB HID v1.10 Device [USB USB Keyboard] on usb-0000:03:00.0-1.1/input1
[  +0.072988] usb 3-1.4: new full-speed USB device number 12 using xhci_hcd
[  +0.098959] usb 3-1.4: New USB device found, idVendor=09da, idProduct=054f, bcdDevice= 1.02
[  +0.000017] usb 3-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  +0.000008] usb 3-1.4: Product: USB Device
[  +0.000005] usb 3-1.4: Manufacturer: A4TECH
[  +0.007414] input: A4TECH USB Device Keyboard as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input37
[  +0.054609] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.0/0003:09DA:054F.000D/input/input38
[  +0.000281] hid-generic 0003:09DA:054F.000D: input,hiddev96,hidraw2: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:03:00.0-1.4/input0
[  +0.001320] input: A4TECH USB Device as /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/usb3/3-1/3-1.4/3-1.4:1.1/0003:09DA:054F.000E/input/input39
[  +0.000245] hid-generic 0003:09DA:054F.000E: input,hidraw3: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:03:00.0-1.4/input1

vs220	# 3 года, 10 месяцев назад
Темы: 25 Сообщения: 8524 Участник с: 16 августа 2009	Vorobuska Отключение Вы его сами отключили или это проявление глюка? Пробовали загружаться с `usbcore.autosuspend=-1` в параметрах ядра?

vs220

# 3 года, 10 месяцев назад

Темы: 25

Сообщения: 8524

Участник с: 16 августа 2009

Vorobuska
Отключение

Вы его сами отключили или это проявление глюка?
Пробовали загружаться с

usbcore.autosuspend=-1

в параметрах ядра?

gentux	# 3 года, 10 месяцев назад
Темы: 3 Сообщения: 119 Участник с: 15 января 2015	А нет ли у Вас renesas chipset? https://lkml.org/lkml/2021/7/28/474

vasek	# 3 года, 10 месяцев назад
Темы: 47 Сообщения: 11933 Участник с: 17 февраля 2013	Vorobuska нормально работает с Windows 8 Значит устройство нормальное, напряжения/питания хватает Vorobuska в Arch Linux в 80% случаев у меня просто отваливается хаб, и порт перестает работать до перезагрузки, с такой же вероятностью он отваливается если я подключаю его с уже загруженной системой А вот в linux имеются определенные проблемы Что имеем - порт USB 3.0 Vorobuska единственный исправный USB 3.0 порт - hub Havic HV-H18 , который явлется USB 2.0 Vorobuska Проблема проявляется с Havic HV-H18 (единственный доступный мне USB hub, нормально работает с Windows 8) - используется ядерный модуль для USB 3.0 - xhci_hcd И предположу, что скорее всего имеется известная проблема, связанная с использованием портов USB 3.0 и устройств USB 2.0 - точнее, некоторые устройства USB 2.0 имеют проблемы в портах USB 3.0 …. производители об этой проблеме знают и в BIOS предусмотрена возможность перевода портов USB 3.0 в режим USB 2.0 (была предусмотрена раньше, как сейчас, не знаю). Рекомендую попробовать перевести в режим USB 2.0 Что можно еще попробовать, при отключении/отказе hub? - переинициализацию USB устройства, думаю нет смыла делать (хотя поэкспериментировать можно), а лучше попробовать выполнить переподключение шины/порта USB. Ошибки не исчезают с опытом - они просто умнеют

vasek

# 3 года, 10 месяцев назад

Темы: 47

Сообщения: 11933

Участник с: 17 февраля 2013

Vorobuska
нормально работает с Windows 8

Значит устройство нормальное, напряжения/питания хватает

Vorobuska
в Arch Linux в 80% случаев у меня просто отваливается хаб, и порт перестает работать до перезагрузки, с такой же вероятностью он отваливается если я подключаю его с уже загруженной системой

А вот в linux имеются определенные проблемы

Что имеем
- порт USB 3.0

Vorobuska
единственный исправный USB 3.0 порт

- hub Havic HV-H18 , который явлется USB 2.0

Vorobuska
Проблема проявляется с Havic HV-H18 (единственный доступный мне USB hub, нормально работает с Windows 8)

- используется ядерный модуль для USB 3.0 - xhci_hcd
И предположу, что скорее всего имеется известная проблема, связанная с использованием портов USB 3.0 и устройств USB 2.0 - точнее, некоторые устройства USB 2.0 имеют проблемы в портах USB 3.0 …. производители об этой проблеме знают и в BIOS предусмотрена возможность перевода портов USB 3.0 в режим USB 2.0 (была предусмотрена раньше, как сейчас, не знаю).
Рекомендую попробовать перевести в режим USB 2.0

Что можно еще попробовать, при отключении/отказе hub? - переинициализацию USB устройства, думаю нет смыла делать (хотя поэкспериментировать можно), а лучше попробовать выполнить переподключение шины/порта USB.

Ошибки не исчезают с опытом - они просто умнеют

vasek	# 3 года, 9 месяцев назад
Темы: 47 Сообщения: 11933 Участник с: 17 февраля 2013	Интересно посмотреть вывод следующих команд (лучше не набирать, а просто скопировать) lspci -nn -vvv \| grep 'USB 3.0' -A 10 \| grep Kernel sudo setpci -s `lspci -nn \| grep 'USB 3.0' \| awk '{print $1}'` d0.l sudo setpci -s `lspci -nn \| grep 'USB 3.0' \| awk '{print $1}'` d8.l Ошибки не исчезают с опытом - они просто умнеют

vasek

# 3 года, 9 месяцев назад

Темы: 47

Сообщения: 11933

Участник с: 17 февраля 2013

Интересно посмотреть вывод следующих команд (лучше не набирать, а просто скопировать)

lspci -nn -vvv | grep 'USB 3.0' -A 10 | grep Kernel
sudo setpci -s `lspci -nn | grep 'USB 3.0' | awk '{print $1}'` d0.l
sudo setpci -s `lspci -nn | grep 'USB 3.0' | awk '{print $1}'` d8.l

Ошибки не исчезают с опытом - они просто умнеют